Pages 59-66 - 2133 Expansion module analogue alarm strings

1. These registers provide the user defined alarm names of each channel of each expansion module when configured as an analogue input.
2. These pages are implemented on the 72xx/73xx, 8xxx/74xx and later families and replace the alarm strings from the old alarm system.

 

59	0	2133 Expansion module 0 input A (low) string	UNICODE	UNICODE	512
	32	2133 Expansion module 0 input A (high) string	UNICODE	UNICODE	512
	64	2133 Expansion module 0 input B (low) string	UNICODE	UNICODE	512
	96	2133 Expansion module 0 input B (high) string	UNICODE	UNICODE	512
	128	2133 Expansion module 0 input C (low) string	UNICODE	UNICODE	512
	160	2133 Expansion module 0 input C (high) string	UNICODE	UNICODE	512
	192	2133 Expansion module 0 input D (low) string	UNICODE	UNICODE	512
	224	2133 Expansion module 0 input D (high) string	UNICODE	UNICODE	512
60	0	2133 Expansion module 0 input E (low) string	UNICODE	UNICODE	512
	32	2133 Expansion module 0 input E (high) string	UNICODE	UNICODE	512
	64	2133 Expansion module 0 input F (low) string	UNICODE	UNICODE	512
	96	2133 Expansion module 0 input F (high) string	UNICODE	UNICODE	512
	128	2133 Expansion module 0 input G (low) string	UNICODE	UNICODE	512
	160	2133 Expansion module 0 input G (high) string	UNICODE	UNICODE	512
	192	2133 Expansion module 0 input H (low) string	UNICODE	UNICODE	512
	224	2133 Expansion module 0 input H (high) string	UNICODE	UNICODE	512
61-62		2133 Expansion module 1 input A-H strings	UNICODE	UNICODE	512
63-64		2133 Expansion module 1 input A-H strings	UNICODE	UNICODE	512
65-66		2133 Expansion module 1 input A-H strings	UNICODE	UNICODE	512

 

 

Page 137 - Active synchronisation and load share configuration

 

1. These registers may be individually read and written at any time.
2. The 72xx/73xx family only supports registers 128-130.

 

Register offset	Name	Minimum value	Maximum value	Scaling factor	Units	Bits/ Sign	Read/Write
	Local bus control (CAN port 0)
0	Device identifier	0	15	1	1	16	Read/Write
1-31	Reserved
	Miscellaneous
32	Generating set run priority	1	16	1	1	16	Read/Write
33	Frequency control offset	0	1.0	0.01	Hz	16	Read/Write
34	Reserved	0	0			16	Read/Write
35	Reserved	0	0			16	Read/Write
36	Load level setting (minimum)	0	100	1	%	16	Read/Write
37	Load level setting (maximum)	0	100	1	%	16	Read/Write
38	Reserved	0	0			16S	Read/Write
39	VAr level setting (maximum)	-100	100	1	%	16 S	Read/Write
40	Bus / Mains load setting	Bus	Mains			16	Read/Write
41	Internal governor IF gain	0	10	0.001	V	16	Read/Write
42	Internal governor IF offset	-10	10	0.001	V	16 S	Read/Write
43	Internal AVR IF gain	0	10	0.001	V	16	Read/Write
44	Internal AVR IF offset	-10	10	0.001	V	16 S	Read/Write
45	Commissioning screens enable flag	0 (no)	1 (yes)			16	Read/Write
46-47	Reserved	0	0			16	Read/Write
	Frequency synchroniser
48	Reserved	0	0			16	Read/Write
49	Relay pulse rate	0.5	2.5	0.01	Hz	16	Read/Write
50	Relay pulse length	0.1	1.6	0.1	Sec	16	Read/Write
51	Gain (proportional gain)	0	0		%	16	Read/Write
52	Compensation (integral gain)	0	100	1	%	16	Read/Write
52-63	Reserved
	Phase synchroniser
64-79	Reserved	0	0			16	Read/Write

Page 137 registers continued

	Load share
80	Reserved	0	0			16	Read/Write
81	Relay pulse rate	0.5	2.5	0.01	Hz	16	Read/Write
82	Relay pulse length	0.1	1.6	0.1	Sec	16	Read/Write
83	Gain (proportional gain)	0	100	1	%	16	Read/Write
84	Compensation (integral gain)	0	100			16	Read/Write
85-95	Reserved
	Voltage matcher
96	Reserved	0	0			16	Read/Write
97	Relay pulse rate	0.5	2.5	0.01	Hz	16	Read/Write
98	Relay pulse length	0.1	1.6	0.1	Sec	16	Read/Write
99	Gain (proportional gain)	0	0	1	%	16	Read/Write
100	Compensation (integral gain)	0	100	1	%	16	Read/Write
101-111	Reserved
	Reactive load control
112	Reserved	0	0			16	Read/Write
113	Relay pulse rate	0.5	2.5	0.01	Hz	16	Read/Write
114	Relay pulse length	0.1	1.6	0.1	Sec	16	Read/Write
115	Gain (proportional gain)	0	100	1	%	16	Read/Write
116	Compensation (integral gain)	0	0			16	Read/Write
117-127	Reserved
	Manual frequency trim
128	Manual frequency trim	-5.0	5.0	0.1	Hz	16S	Read/Write
129	Minimum frequency trim	-5.0	5.0	0.1	Hz	16S	Read
130	Maximum frequency trim	-5.0	5.0	0.1	Hz	16S	Read
131-136	Reserved
136-255	Reserved

 

 

 

Page 142 – ECU Trouble Codes

 

1. Reading register 0 effectively latches a copy of the trouble code list at that time and so allows the list to be read without risk of the contents changing until register 0 is re-read. This also applies to reading the short descriptive strings for the trouble codes (see following pages), so that the list of trouble codes can be read in one or more sections and then the associated strings read as needed. To see any updates to the list, the PC needs to re-read register 0 and so latch the list once more.

 

Registers

Register offset	Name	Minimum value	Maximum value	Scaling factor	Units	Bits/ sign	Read/write
0	Number of trouble codes	0	50			16	Read only
1	Amber warning lamp status	0	1			1/16	Read only
	Red stop lamp status	0	1			2/16	Read only
	Reserved for SAE assignment					3-16/16	Read only
2-5	Trouble Code 1					64	Read only
6-9	Trouble Code 2					64	Read only
10-13	Trouble Code 3					64	Read only
14-201	Trouble Codes 4-50						Read only
202-255	Reserved						Read only

 

 

Trouble code format

Register offset	Name	Minimum value	Maximum value	Scaling factor	Units	Bits/ Sign
0--1	Trouble code value	0	524287			9-32/32
	Additional trouble code status	0	255			1-8/32
2	Engine type code	0	31			16
3	reserved	0	0			16

 

⇐ Предыдущая14151617181920212223Следующая ⇒

Поделиться: