Page 8 registers continued

8	Generator failed to close	0	15		13/16-16/16
	Mains failed to close	0	15		9/16-12/16
	Generator failed to open	0	15		5/16-8/16
	Mains failed to open	0	15		1/16-4/16
9	Mains low voltage	0	15		13/16-16/16
	Mains high voltage	0	15		9/16-12/16
	Bus failed to close	0	15		5/16-8/16
	Bus failed to open	0	15		1/16-4/16
10	Mains low frequency	0	15		13/16-16/16
	Mains high frequency	0	15		9/16-12/16
	Mains failed	0	15		5/16-8/16
	Mains phase rotation wrong	0	15		1/16-4/16
11	Generator phase rotation wrong	0	15		13/16-16/16
	Maintenance due	0	15		9/16-12/16
	Clock not set	0	15		5/16-8/16
	Local LCD configuration lost	0	15		1/16-4/16
12	Local telemetry configuration lost	0	15		13/16-16/16
	Control unit not calibrated	0	15		9/16-12/16
	Modem power fault	0	15		5/16-8/16
	Generator short circuit	0	15		1/16-4/16
13	Failure to synchronise	0	15		13/16-16/16
	Bus live	0	15		9/16-12/16
	Scheduled run	0	15		5/16-8/16
	Bus phase rotation wrong	0	15		1/16-4/16
14	Priority selection error	0	15	13/16-16/16
	Multiset communications (MSC) data error	0	15	9/16-12/16
	Multiset communications (MSC) ID error	0	15	5/16-8/16
	Multiset communications (MSC) failure	0	15	1/16-4/16
15	Multiset communications (MSC) too few sets	0	15	13/16-16/16
	Multiset communications (MSC) alarms inhibited	0	15	9/16-12/16
	Multiset communications (MSC) old version units	0	15	5/16-8/16
	Mains reverse power	0	15	1/16-4/16
16	Minimum sets not reached	0	15	13/16-16/16
	Insufficient capacity available	0	15	9/16-12/16
	Expansion input unit not calibrated	0	15	5/16-8/16
	Expansion input unit failure	0	15	1/16-4/16
17	Auxiliary sender 1 low	0	15	13/16-16/16
	Auxiliary sender 1 high	0	15	9/16-12/16
	Auxiliary sender 1 fault	0	15	5/16-8/16
	Auxiliary sender 2 low	0	15	1/16-4/16
18	Auxiliary sender 2 high	0	15	13/16-16/16
	Auxiliary sender 2 fault	0	15	9/16-12/16
	Auxiliary sender 3 low	0	15	5/16-8/16
	Auxiliary sender 3 high	0	15	1/16-4/16
19	Auxiliary sender 3 fault	0	15	13/16-16/16
	Auxiliary sender 4 low	0	15	9/16-12/16
	Auxiliary sender 4 high	0	15	5/16-8/16
	Auxiliary sender 4 fault	0	15	1/16-4/16
20	Engine control unit (ECU) link lost	0	15	13/16-16/16
	Engine control unit (ECU) failure	0	15	9/16-12/16
	Engine control unit (ECU) error	0	15	5/16-8/16
	Low coolant temperature	0	15	1/16-4/16
21	Out of sync	0	15	13/16-16/16
	Low Oil Pressure Switch	0	15	9/16-12/16
	Alternative Auxiliary Mains Fail	0	15	5/16-8/16
	Loss of excitation	0	15	1/16-4/16

 

 

Page 8 registers continued

22	Mains kW Limit	0	15	13/16-16/16
	Negative phase sequence	0	15	9/16-12/16
	Mains ROCOF	0	15	5/16-8/16
	Mains vector shift	0	15	1/16-4/16
23	Mains G59 low frequency	0	15	13/16-16/16
	Mains G59 high frequency	0	15	9/16-12/16
	Mains G59 low voltage	0	15	5/16-8/16
	Mains G59 high voltage	0	15	1/16-4/16
24	Mains G59 trip	0	15	13/16-16/16
	Generator kW Overload	0	15	9/16-12/16
	Engine Inlet Temperature high	0	15	5/16-8/16
	Bus 1 live	0	15	1/16-4/16
25	Bus 1 phase rotation wrong	0	15	13/16-16/16
	Bus 2 live	0	15	9/16-12/16
	Bus 2 phase rotation wrong	0	15	5/16-8/16
	Reserved	0	15	1/16-4/16
26-32	Unimplemented
33-127	Reserved

 

Page 8 registers continued

128	Number of unnamed digital inputs	0	128	16
129	Unnamed digital input 1	0	15	13/16-16/16
	Unnamed digital input 2	0	15	9/16-12/16
	Unnamed digital input 3	0	15	5/16-8/16
	Unnamed digital input 4	0	15	1/16-4/16
130	Unnamed digital input 5	0	15	13/16-16/16
	Unnamed digital input 6	0	15	9/16-12/16
	Unnamed digital input 7	0	15	5/16-8/16
	Unnamed digital input 8	0	15	1/16-4/16
131	Unnamed digital input 9	0	15	13/16-16/16
	Unnamed digital input 10	0	15	9/16-12/16
	Unnamed digital input 11	0	15	5/16-8/16
	Unnamed digital input 12	0	15	1/16-4/16
132	Unnamed digital input 13	0	15	13/16-16/16
	Unnamed digital input 14	0	15	9/16-12/16
	Unnamed digital input 15	0	15	5/16-8/16
	Unnamed digital input 16	0	15	1/16-4/16
133	Unnamed digital inputs 17-20	0	15	16
134	Unnamed digital inputs 21-24	0	15	16
135	Unnamed digital inputs 25-28	0	15	16
136	Unnamed digital inputs 29-32	0	15	16
137	Unnamed digital inputs 33-36	0	15	16
138	Unnamed digital inputs 37-40	0	15	16
139	Unnamed digital inputs 41-44	0	15	16
140	Unnamed digital inputs 45-48	0	15	16
141	Unnamed digital inputs 49-52	0	15	16
142	Unnamed digital inputs 53-56	0	15	16
143	Unnamed digital inputs 57-60	0	15	16
144	Unnamed digital inputs 61-64	0	15	16
145	Unnamed digital inputs 65-68	0	15	16
146	Unnamed digital inputs 69-72	0	15	16
147	Unnamed digital inputs 73-76	0	15	16
148	Unnamed digital inputs 77-80	0	15	16
149	Unnamed digital inputs 81-84	0	15	16
150	Unnamed digital inputs 85-88	0	15	16
151	Unnamed digital inputs 89-92	0	15	16
152	Unnamed digital inputs 93-96	0	15	16
153	Unnamed digital inputs 97-100	0	15	16
154	Unnamed digital inputs 101-104	0	15	16
155	Unnamed digital inputs 105-108	0	15	16
156	Unnamed digital inputs 109-112	0	15	16
157	Unnamed digital inputs 113-116	0	15	16
158	Unnamed digital inputs 117-120	0	15	16
159	Unnamed digital inputs 121-124	0	15	16
160	Unnamed digital inputs 125-128	0	15	16
161-255	Reserved

 

 Alarm condition codes

Condition	Meaning	Displayed string
0	Disabled digital input	None
1	Not active alarm	None
2	Warning alarm	Active string
3	Shutdown alarm	Active string
4	Electrical trip alarm	Active string
5-7	Reserved
8	Inactive indication (no string)	None
9	Inactive indication (displayed string)	Inactive string
10	Active indication	Active string
11-14	Reserved
15	Unimplemented alarm	None

 

Notes on alarm codes

1. An alarm that is fitted but disabled by the configuration of the slave device returns code 0.

2. An alarm that is not implemented on a particular control unit returns code 15.

3. An indication that does not require a message to be displayed when inactive returns either code 8 or 10.

4. An indication that does require a message to be displayed when inactive returns either code 9 or 10.

5. The inactive strings are only required for indications, in all other cases they will contain 32 spaces.

 

⇐ Предыдущая78910111213141516Следующая ⇒

Поделиться: